The Actuator 24 V standard is a thermoelectric actuator for opening and closing valves on waterborne heating and cooling systems.
Features, as protection in case of leaky valves, compact and modern casing, versions in normally closed and normally open, valve adapter concept and an enhanced life time makes the actuator competitive and flexible.
The actuator 24 V is controlled by a 24 V room thermostat with two-point output or pulse-width modulation.

Architect is an active chilled beam for exposed installation that provides great freedom of choice in design. Easy applicable with three predefined cover design solutions with great flexibility to create a customised design, without affecting the function and performance. One big advantage is that you can do you planning without having to decide on the design. This allows you to retrofit the design in a simple way.

Architect can be equipped with cooling, heating, ventilation, Regula Secura condensation guard, built-in valves, actuators and built-in lighting (special).

• Freedom in architectonic design
• JetCone technology
• Low building height – 175 mm
• Adaptable with lighting
• Eurovent certified

Atrium-C is a cooling panel. It is equipped with endpieces and can be installed recessed into a suspended ceiling. The top of the Atrium-C is not insulated.

Atrium-C is available in a hygienic design with the top covered. The hygienic design is suitable for washing bays or suchlike..

• The lightest cooling panel on the market
• High degree of radiant cooling
• Easy to clean
• Available in lengths up to 6m

Atrium-H is a heating panel. It is equipped with endpieces and can be installed recessed into a suspended ceiling. The top of the panel is insulated with extruded polystyrene foam. The foamed plastic is manufactured without the addition of CFC or HCFC gas,i.e. Freons.

Atrium-H should be used if the panel is to provide both cooling and heating with a so-called "Change-Over" system

Atrium-H is available in a hygienic design with the top covered. The hygienic design is suitable for washing bays or suchlike.

• The lightest heating panel on the market
• High degree of radiant heating
• Easy to clean
• Available in lengths up to 6 m

Atrium Plana is a heating and cooling panel. It has a flat surface which makes its appearance similar to the false ceiling, and can be installed recessed or into a suspended ceiling.
Atrium Plana is a discreet and unique panel solution from Lindab. Atrium Plana the lightest cooling panel on the market

• High degree of radiant cooling and heating
• Easy to clean
• Discreet appearance

Carat is placed above a perforated suspended ceiling and supplies cooling, with a low air velocity, to the room below.

Carat has a high radiation quotient of approx. 35% (compared to approx. 5% for traditional finned products). This gives great freedom in placing, when installing Carat, yet keeps air velocities low.

Carat can be used for cooling. It can be equipped with the Regula Connect condensation guard feature. It offers many possibilities and great flexibility. For example, it is possible to paint Carat any colour you want.

• High degree of radiant cooling – 35%
• Creates low air velocities
• Lengths up to 6m
• Can be connected in series

Celo, which can be installed above a suspended ceiling. Thus, you can conceal the ventilation and cooling features and create an unbroken ceiling without visible technical installations. The Celo concept has been developed together with Ecophon, which provides acoustic ceilings adapted for the system.

• Fan-shaped distribution pattern
• For installation above acoustic ceiling
• Eurovent certified

CO2RT-R-LB is a room sensor for measuring carbon dioxide levels in air. It has a builtin relay with switching output.

• Built-in relay
• CO₂-level 0 … 2000 ppm
• Excellent long term stability
• Snap-in cover

Lindab’s CO2RT-R-LB with patented auto calibration process sets new standards in CO₂ measuring for HVAC applications.

A range of room transmitters for measuring carbon dioxide concentration in indoor environments. The transmitter has a built-in CO₂ sensor with working range 0...2000 ppm and output signal 0...10 V, as well as a built-in PT1000 temperature sensor with separate terminals.

• Output signal CO₂, 0...10 V DC referring to 0...2000 ppm
• Temperature sensor, 0...10 V DC referring to 0...50°C and
• PT1000 class DIN B
• CO₂ concentration, 0...2000 ppm
• Temperature, 0...50°C
• Good long-term stability
• RCBC algorithm

Transmitters with automatic calibration combining measurementof CO₂ level and temperature in the same casing. The sensors are mounted in the cover-part of the casing. The cover is easy to detach from the back by means of snap-in grips and detachable terminals. This makes mounting easier. Furthermore, no cables have to be disconnected, simplifying service and replacement.

The transmitters are intended for wall mounting in HVAC systems.

Fasadium is an efficient system designed to handle low air pressures. Typical environments where Fasadium is used include, for example, schools, hospitals and offices.

Fasadium can be used for cooling, heating and ventilation. Fasadium is supplied as standard with valves, flexible pipe connections and a connection card for the Regula Connect control system. Additional features that can be integrated into Fasadium include, for example, Regula Combi and the Regula Secura condensation guard.

• Adapted for high air pressures
• Cooling and heating in one unit
• Equipped with service hatch for easy accessibility
• Eurovent certified

IR24-P is a presence detector designed for automatic ventilation control of HVAC systems. It saves money and gives higher comfort in premises which require forced ventilation for shorter periods of time, such as conference rooms, assembly-halls etc.The unit provides a changeover relay signal output for start/stop of fan or similar equipment. It can be wall or corner mounted with 110°, 15 m detection range.

• Power supply 24 V AC or DC
• Intended for wall or ceiling mounting
• Unobtrusive design
• Potential free, changeover relay
• Both relay on-delay and/or relay off-delay, can be individually set

2-way control valve with push fitting connection and toolless presetting to be controlled by thermoelectric actuators. The valves are specially developed for the demands of chilled beams and other waterborne products.
Equipped with Lindab thermostatic actuators, the valves can achieve a linear valve characteristic (best with APR-40405), which guarantees best temperature control and lowest energy loss during operation. The special valves show extremely low sound generation in combination with Lindab chilled beams which offers a wider range for recommended pressure loss over the beam.
A white protective cap with Lindab logo and a printed logo on the valve body easily identifies the models.

• Specially developed for chilled beams
• Fast push fitting connections (for copper pipes)
• Toolless presetting
• Brass finish
• Connection to actuator: M28 x 1.5 [mm]
  

For straight version, go to LinFlow-S.

2-way control valve, with push fitting connection and toolless presetting, to be controlled by thermoelectric actuators. The valves are specially developed for the demands of chilled beams and other waterborne products.
Equipped with Lindab thermostatic actuators, the valves can achieve a linear valve characteristic (best with APR-40405), which guarantees best temperature control and lowest energy loss during operation. The special valves show extremely low sound generation in combination with Lindab chilled beams which offer a wider range for recommended pressure loss over the beam.
A white protective cap with Lindab logo and a printed logo on the valve body easily identifies the models.

• Specially developed for chilled beams
• Fast push fitting connections (for copper pipes)
• Toolless presetting
• Brass finish
• Connection to actuator: M28 x 1.5 [mm]
  

For angled version, go to LinFlow-A.

Loggia is the brand name of Lindab's heating strips. What distinguishes Loggia from Atrium-H is that it does not have end-pieces on its short sides. Loggia is therefore not designed for installation in the supporting structure of a suspended ceiling (see picture 3). Loggia is suited for industrial premises, for example, warehouses, showrooms, etc. The top of the panel is insulated with extruded polystyrene foam. The foamed plastic is manufactured without the addition of CFC or HCFC gas, i.e. Freons.

• The lightest heating panel on the market
• High degree of radiant heating
• Easy to clean
• Available in lengths up to 6 m

Lindab’s supply air beam unit Munio can be used for cooling, heating and ventilation. It has been developed for the installation and integration into bulkheads for example in hotels, in hospitals or for any other rooms with bulkheads.

• Small dimensions (800 x 540 x 170), high capacity
• Ventilation, cooling and heating as standard
• JetCone, an innovative way of regulating the air volume
• No need for filter because of it works with dry cooling
• Service & maintenance issues are limited
• For bulkhead installation with full integration in architectural design
• Easy installation
• Telescoping connection with clip in for outlet front grill
• Full access with low cost maintenance
• Fulfils highest hygienic requirements
• Low sound levels
• Individual room regulation with Customized control equipment (plus)
• Additional energy savings when used with free energy sources
• Lindabs active chilled beams are Eurovent-certified and tested according to EN-15116.

Plafond's function is based on the induction principle. Ventilation air with a certain dynamic pressure is released through specially-formed nozzles into a dispersal zone, thereby creating a low static pressure. This low pressure causes warm air from the room to be sucked towards the ventilation air passing through the battery. The volume of the warm indoor air is 4 to 5 times that of the ventilation air. The air is cooled as it passes through the battery, which consists of aluminium ribs with copper ducts filled with cold running water. The heat of the room is absorbed through the aluminium ribs and then transferred through the copper pipe to the water circuit and on to a central cooling unit.

• For visible installation in corner
• Fan-shaped distribution pattern
• Eurovent certified

...

Lindab´s new Plafond XD is basically an exposed design active chilled beam solution for ventilation, cooling and heating which helps you to create a perfect indoor climate in rooms without suspended ceilings.
The new concept with separate technical Body and (Design-)Cover, available in many different designs make the new Plafond XD function 100 % as a corresponding architectural element fitting into your room and building architecture.
All technical parts as the Plafond XD Body, connections, cabling, valves, actuators and other plus features or accessories, can easily be hidden behind Plafond XD Cover.

• The primary air volume can be pre-adjusted in the factory and later easily be re-adjusted with Lindab’s tool less patented JetCone system,
• The Angled Nozzles system for air outlet, secures a perfect air spread pattern that reduces draft risk without losing capacity.
• The Plafond XD Cover is available in seven different designs.
• The beam can be easily integrated/used in a Pascal water system to enable VAV/DCV.
• Lindab´s active chilled beams are Eurovent-certified and tested according to EN-15116.

Lindab’s unit Plexus gives many placement possibilities since it fits into the false ceiling 600 x 600 alternative 1200 x 600.

Plexus is provided with Angled Nozzles which are controlling the primary air into non-parallel jets in a 360 degree air pattern. The 360 degree air pattern results in shorter air throws (30%) and a draft free indoor climate. Plexus can be used for both cooling, heating and ventilation. Plexus can be equipped with the functions, Regula Secura condensation guard, down fold battery for better accessibility and premounted valves and actuators. The possibilities are many and the flexibility large.

• Unique 360° diffusion pattern
• Flexible JetCone technology
• Revolutionary heating solution
• Eurovent certified

Lindab's supply air beam Premax can be used for cooling, heating and ventilation. Water valves, actuators, Regula Secura, Regula Combi and Regula Connect can all be built into the Premax beam.

Premax features the Lindab JetCone, an innovative way of regulating the air volume. The air volume can easily be adjusted without having to worry about pressure and noise issues. The Angled Nozzle system secures a perfect air spread pattern, available in a number of factory preset angles.
As a plus feature the Lindab AirGuide system offers readjustable air spread pattern control.

• Powerful – exceptional cooling performance
• Flexibility – adapt to the individual workspace
• Control – innovations eliminating draughts

Lindab's supply air beam Premum can be used for cooling, heating and ventilation. Water valves, actuators, Regula Secura, Regula Combi and Regula Connect can all be built into the Premum beam.

Premum features the Lindab JetCone, an innovative way of regulating the air volume. The air volume can easily be adjusted without having to worry about pressure and noise issues.

The Angled Nozzles system secures a perfect air spread pattern, available in a number of factory preset angles.

As a plus feature the Lindab AirGuide system offers readjustable air spread pattern control.

• JetCone – wide dynamic operation range
• Angled Nozzles – draught free environment
• AirGuide – for a maximum in flexibility

Lindab's high performance active chilled beam Professor XP provides great freedom for the installation, as its inset height is lowest in the market, with an overall height of 120 mm only. It is available from 1.2 m up to 3.6 m length.
Professor XP is equipped with pre-set divergent nozzles, which provides a draft-free indoor climate and can be used for cooling, heating and ventilation. Professor XP can be furnished with the following features cooling, heating, ventilation, Regula Secura condensation guard, Regula connect cards, built-in valves and actuators, etc. LED lighting can be integrated on request. It offers many possibilities and great flexibility.
Professor XP is available with both 2-pipe and 4-pipe water connection and can be installed both exposed free hanging (F-; 120 mm) or recessed in a suspended ceiling (I-; 144 mm) in: single- and open offices, meeting rooms, entrance halls, schools, kinder gardens, banks, etc.
The new powerful battery concept from Lindab, from now on integrated in the Professor XP, offer 11 different standard battery types for Professor XP included both 2-pipe and 4-pipe water circuits. Always the best choice.
Lindab´s active chilled beams are Eurovent-certified and tested according to EN-15116.
Professor XP is available as standard, in signal white RAL 9003 or in pure white RAL 9010, gloss value 30. Other RAL colours on request.

• Low building height – only 120mm
• Battery types – always optimised energy use
• Fan-shaped distribution pattern – low draft risk
• High hygiene – easy to clean
• Adaptable with lighting, exhaust etc.
• Eurovent certified

Lindab Solus is specially designed as a combined HTC and LTH beam—High Temperature Cooling and Low Temperature Heating. Due to the customized coil, the Solus beam delivers an outstanding cooling and heating effect per degree temperature difference between the water circuit and the room temperature. This means that you get great capacities, at a relatively high running temperature. All in all, the Solus beam can save a lot of the energy cost on cooling and heating.

• Cost saving high output beam that delivers an excellent capacity for both cooling and heating, while running the same temperature set for both functions.
• Pressure authority in the beam means that regulation of the air pressure is a fast and easy task.
• Lindabs active chilled beams are Eurovent-certified and tested according to EN-15116.

Clamp on sensor with cable. TG-A1/PT1000 is a temperature sensor with PT1000 element for surface temperature measurement.

• Adjustable to pipe diameter
• Rapid temperature transfer between pipe and sensor
• Mounting strap included
• Simple and quick installation

Clamp-on sensor with cable for mounting on pipe.

For measuring surface temperature. For use with the Aqualine, TM- and TTC-series. Delivered with clamp.

N.B. This sensor can not be used with the Pulser -series.

TG-K3/PT1000 is a temperature sensor with included cable and with a PT1000 element for air temperature measurement in ventilation ducts

• Adjustable insertion length
• Supplied with 1.5 meter cable
• Simple and quick installation
• IP20

Duct sensor with cable for mounting in ventilation ducts.

....

Room sensor range with a modern design for all environments.

• Modern design
• Simple and quick installation with snap on lid

TG-R5... are room sensors intended for use with the Aqualine, PULSER, TM, TTC, Prigo and Floorigo ranges.

Sensor with NTC-element for measuring room temperature.

Resistance measurements can only be made when the sensor is not connected to a controller.